How to change filter?

Before installing your filter, lightly coat its rubber seal with fresh oil. The oil filter wrench also has to be changed. Install a new filter in it and tighten the lid. If you get custom built-in tool storage, power tail gates and more, multiple additions of things you may not use often or even need will add to the price as well. Any expert doesn't need to do it. If the service engine soon light doesn't come back on. Problem with these Ford engines is the coil pack electrodes corrode causing misfire and the check engine light to go on! Alignment issues will accelerate tires wear and cause your engine to work harder. When switched to the "Main" position, fuel flows from the main tank directly to the engine and the fuel gauge indicates the amount of fuel in the main tank.

We are one of leading auto engine tool manufacturers, welcome to consult us!

Do you know tire inspection?

Today I will tell you some test about auto, hoping to help you. You'd better have a tire repair tool.

External test

1. remove the wheel from the car care

2. tire inflation – in control under pressure recommended by the manufacturer (based on tire-wall)

3. the tires into the testing tank, leak parts have been found. High pressure leak appears under certain conditions (in the load overload effect), then you will need to use a leak detector to find the damage area. Caution test, beware many of the damaged air leakage.

4. refer to "not (industry standard)" (outside). When the tires to determine needs and can be patched with a marker in the repairability of tires before doubt, you should not repair steps.

Internal test

5. remove the tire from the wheel on the ground.

6. in the light of "can not be repaired (industry standard)" (inside). When the tires to determine needs and can be patched with a marker in the tire marks on the internal tire damage done.

7. removed cause tire damage foreign material, carefully measured to ensure passenger car tire damage the diameter of 1/4 inches or less, light (middle), truck tire damage the diameter of 3/8 inches or less. If the damage exceeds the above, that should be given to removing the tire to comprehensive professional repair service repair make larger cross section.

8. use the probe, remove it from the outside insert the tire until it through the airtight layer 1/4 inch. Be careful to prevent sticking out of the other hole.

9. the probes inserted into the cut holes to the point of keeping the "12 o'clock" position, the mushroom nail hole close to a probe into injury, makes mushroom nail the center hole Center to injury.

10. when the penetration angles less than 25 degrees, use a holistic approach to repair (full mushroom nail).

11. when the penetration angles greater than 25 degrees, repair must be two discrete methods (principles equivalent to separate the mushroom patch parts of the nail and rod).

12. tyre placed on the wide tires, makes wound hole in "4 o'clock" or "8 o'clock" position. -Bead too open.

Is engine washing gun for you?

Our air engine washing gun is the perfect tool for not only cleaning the engine bay, but also anywhere around the home or workshop. Designed to be filled with detergents and non-corrosive cleaning products, the cleaning gun works its magic allowing you to not only get into those hard to reach spaces, but cut through the grease and grime at the same time. The 750mL container allows you to focus on the job at hand, and an included simple, Nitto style fitting gives peace of mind.

• 750mL container capacity
• Nitto style air fitting included
• Ideal for cleaning or degreasing
• Suitable for non-acidic/non-corrosive liquids
• Powder coated gun body with aluminium container

If you want engine washing gun, please contact us!

How much you know ball joint separator?

We are ball joint separator manufacturer and we will provide some knowledge about ball joint separator.

The first signs of a failing ball joint include loud banging over bumps and/or sloppy steering as the joint separates out of its socket. A typical safety inspection should measure the amount of motion in your ball joint, and only allow a safe amount to pass. You can test ball joint play yourself on McPherson spring struts that do not put any load on the ball joint by lifting the car and manhandling the wheel. This design is rare, however, because most suspension springs apply constant pressure on the assembly.

If your car has a spring that puts load on either the upper or lower ball joint, you will need to remove that spring pressure by positioning your jack under the control arm and jacking it a few inches up to relieve the spring pressure on the ball joint. If the design allows, you can use a special ball joint support tool like the one made for the Saab 900 to hold everything in place. You can also relive tension with standard spring compressors, which is a common way of doing this.

If you find ball joint separator supplier in China, you can send your email to info@autotoolsdepot.com.

How much you know battery tester?

It's important to test your battery and electrical system regularly, not just when it’s starting to show signs of weakness. So, it is necessary to have a battery tester. Proactively testing it (or making sure your mechanic does) twice a year will help reduce your chances of failure. Most retailers offer a simple free five minute battery test. Use our Find a Retailer for a location near you to get a free battery test.

Fully charged automotive batteries should measure at 12.6 volts or above. When the engine is running, this measurement should be 13.7 to 14.7 volts. If you don’t have a multimeter to tell you the voltage of your battery, you can do a test of your electrical system by starting the car and turning on the headlights. If they are dim, that indicates the lights are running off the battery and that little or no charge is being produced by the alternator. If the lights get brighter as you rev the engine, it means the alternator is producing some current, but may not be producing enough at idle to keep the battery properly charged. If the lights have normal brightness and don’t change intensity as the engine is revved, your charging system is probably functioning normally. If you’ve been experiencing problems with your battery system and the headlight test checks out okay, you should check whether or not the battery is holding a charge, or if something on the vehicle is discharging it.

We provide high quality battery tester.

Do you know magnetic tray?

Magnetic tray has many uses. Keep loose nuts, screws and other small metal items in reach. Smooth stainless steel trays have powerful ceramic magnets with rubber covers in the base to secure the tray to a metal toolbox or table while keeping important metal pieces at hand. Store metal parts and tools during assembly and disassembly. Ideal for mechanics, craftsmen and hobbyists.

• Works in any position - flat, sideways or upside down
• Heavy gauge, stainless steel with rubber base to prevent scratching
• Great for jobsite, garage, office and home

Learn more magnetic tray via www.autotoolsdepot.com.

Do you learn the development of auto tools?

With the improvement of automotive technology, the growth of car ownership, the development of car repair market, there are a number of modern enterprises entering the auto maintenance industry in the past decade. They began to produce and provide various professional auto maintenance equipment, especially Ball Joint Separator, Disc Brake Piston Separator, Coil Spring Compressor. There are a large number of overseas exports, we are one of them.

In national policy guidance, the Chinese auto maintenance industry has a thriving development. China's auto maintenance equipment after years of expansion, already has a considerable scale and pace of development. China is currently engaged in auto maintenance equipment development, production and marketing enterprises, about 1500, the annual output of about 10 billion. China continued prosperity auto maintenance industry trend, business volume and revenue continued to grow, equipment manufacturers to maintain rapid growth within the industry business model shift.

Welcome to consult auto tools from China, welcome to consult engine tools from our company.

How does the air duster gun work?

Air duster gun is the principle of using air amplification, effectively reducing the consumption of compressed air, resulting in a strong and accurate airflow, and drive the surrounding air to work together. Dust guns are mainly used for dust, dust, or foreign matter on any type of workpieces for use in factories, mechanical workshops, woodworking and installation. Can be used in some of the hands of some of the relatively narrow, high, inside the machine parts and trachea cleaning work.

Our company specializes in manufacture, supply and export air duster gun. It has always been our focus to manufacture the finest Air Tools / Pneumatic Tools and to deliver them on time with attentive after-sales service.