Have You Mastered The Correct Posture Of Using Air Duster Gun?

The Air Duster Gun has a simple structure and is easy to use, but it requires proper using.

There are many factors that affect the use of guns,like painted objects,painted materials,and even seasons.The key to the use of the gun is to adjust the control of the knob,the distance between the grasping of the spray gun and the speed of the user’s movement,as well as the proximity of the layers of the overlap.The spraying distance, spraying running and spray pattern is three spraying Principles,they are also the basis of spraying technology,must be familiar with,and strictly abide by.

Spray guns are essential for efficient coating. With the progress of manufacturing technology and the application of new materials, modern spray gun is moving into the direction of high durability, fine atomization , spray gun structure is more and more scientific.Although there are many types of guns,their structures are roughly same.Generally it is constituted with tip, adjusting knob and body.

Our company is an air duster gun manufacturer, we provide varies of guns and knowledge about them.

Ball joint separator you may know

We are ball joint separator manufacturer and we will provide some knowledge about ball joint separator.

The first signs of a failing ball joint include loud banging over bumps and/or sloppy steering as the joint separates out of its socket. A typical safety inspection should measure the amount of motion in your ball joint, and only allow a safe amount to pass. You can test ball joint play yourself on McPherson spring struts that do not put any load on the ball joint by lifting the car and manhandling the wheel. This design is rare, however, because most suspension springs apply constant pressure on the assembly.

If your car has a spring that puts load on either the upper or lower ball joint, you will need to remove that spring pressure by positioning your jack under the control arm and jacking it a few inches up to relieve the spring pressure on the ball joint. If the design allows, you can use a special ball joint support tool like the one made for the Saab 900 to hold everything in place. You can also relive tension with standard spring compressors, which is a common way of doing this.

If you find ball joint separator supplier in China, you can send your email to info@autotoolsdepot.com.

Method of Maintenance of Air Blower Gun

In the maintenance of the soot blower, the power supply must be cut off and the steam line valve in front of the blower valve shall be turned off, in case the air duster gun can initiate or other electrical accidents. 

Regularly check the seals for leakage. If there is a leak, adjust the compression of the packing properly; The packing gland can be replaced if the problem is still unsolved. When the sealing ring of the hollow shaft is replaced, the V type opening should be loaded in the direction of the stem. 

If there is a leak after the valve is closed, it is indicated that the combination of the seat ring and the disc shall be worn or deformed, and shall generally be re-ground the sealing surface. The body must be replaced if the cover is damaged enough to be insufficient to solve. 

Grease the oil regularly. The decelerate box is once a month, starting arm and copper sleeve once a week. 

The air duster gun should be disintegrated once a year, often check the stroke switch and regularly clean up the soot on the blower. 

If the load of the motor is too heavy, check that the ash gun is bent. If bending should be taken out straighter in time. 

When use air duster gun you must know

There are many air duster guns in car industry, here I will tell you some considerations you must know as followings:

1. Must be installed in accordance with the operating instructions before use.

2. Blowing guns need to be connected to the compressor.

3. Keep the dust gun clean, oil free and fouling.

4.Regular cleaning of the dust gun to prevent a large number of other objects accumulated in the dust gun parts above, clean, should cut off the power.

5. Can not be used in environments containing flammable gases and large amounts of dust.

6. Non-professional personnel can not be repaired without authorization.

Our company is an air duster gun manufacturer, we provide varies of guns and knowledge about them.

The steps of changing oil(2)

When you have an oil filter wrench, you also need do as followings:

6. After the oil has drained (give it 10-30 minutes for a good drain if you have the time), wipe away oil residue from the oil pan and put the drain plug back in. Tighten it firmly, but don’t overdo it. Your owner’s manual will have the exact torque required.

Do me (and other animals) a favor, clean up oil leaks and don’t dispose of oil in your yard, streams, or waste-water drains. Your favorite Advance store will safely dispose of your used oil for free! Available at most of our 3,500 stores (unless prohibited by law).

7. Reposition your drain pan by the oil filter and remove it using your oil filter wrench (or hand if it will budge). Some wrenches work from the end, while others wrap around the filter.

8. If your filter still won’t budge, puncture it with a screwdriver at its lowest point to drain, then use the same screwdriver to spin off the filter. A little more oil will come out when you spin off the filter, so have your rags handy.

9. Apply a film of clean oil to the top of the new filter gasket. Then spin the filter on using only your hand. Go ¾ of a turn after you feel the gasket make contact with the engine after spinning it on.

oil change tips10. Double check the filter and drain plug for tightness, then fill your engine with the recommended viscosity and amount of motor oil. (Again, your owner’s manual will provide this).

11. Determine your oil level using the dipstick, then check for any leaks. Start the engine and check for leaks again. Bring used motor oils to Advance for proper disposal or recycling.

Well, that’s a wrap. You can now safely do your own oil ch

The steps of changing oil(1)

First, you must have an oil filter wrench. Then I will tell you 10 steps of changing oil as followings:

1. Securely raise your vehicle on ramps or jack-stands (use a jack lift for the latter). Makes sure to put blocks behind your tires. If you can safely get under your vehicle without needing to raise it, then go for it.

2. Warm up the engine for a couple minutes to get the oil warm (but not too long or the oil will be hot). Raise your hood and open the oil cap on top of your engine to let the old oil drain faster.

3. Get under the car and position your drain pan under the oil plug (account for the initial stream of oil shooting out further than directly under the plug).

4. Using your wrench, loosen the plug a few turns. Then finish loosening the plug with your hand, quickly pulling it away when the oil is starting to drain out. Be careful of hot motor oil (gloves help in this case).

5. Wipe the drain plug while the oil drains and inspect it for bent or broken threads. Replace the sealing washer if cracked or worn, or use a new metal crush washer if needed.

I will tell you the others in next news, learn more oil filter wrench via www.autotoolsdepot.com.

Do you hear ball joint separator?

We are ball joint separator manufacturer and we will provide some knowledge about ball joint separator.

The first signs of a failing ball joint include loud banging over bumps and/or sloppy steering as the joint separates out of its socket. A typical safety inspection should measure the amount of motion in your ball joint, and only allow a safe amount to pass. You can test ball joint play yourself on McPherson spring struts that do not put any load on the ball joint by lifting the car and manhandling the wheel. This design is rare, however, because most suspension springs apply constant pressure on the assembly.

If your car has a spring that puts load on either the upper or lower ball joint, you will need to remove that spring pressure by positioning your jack under the control arm and jacking it a few inches up to relieve the spring pressure on the ball joint. If the design allows, you can use a special ball joint support tool like the one made for the Saab 900 to hold everything in place. You can also relive tension with standard spring compressors, which is a common way of doing this.

If you find ball joint separator supplier in China, you can se

4 types of ball joint separator(2)

Automobile undercarriages differs widely, and so do ball joint separator designs. Before undertaking their next ball joint replacement job, mechanics should understand what is needed to secure the best deal on their preferred ball joint separator.

Hydraulic Type

Hydraulic format ball joint separators support between 8 and 12 tonnes of weight. As with the scissor type, they are suitable for confined spaces and consist of heavily reinforced steel, but jaw widths can span up to 56mm. Available both separately and in ball joint separator kits, they are ideal for commercial vehicles and small lorries.

Choosing Tool Type

Although the previously discussed ball joint separator formats are among the most well-liked by mechanics, there are many other types that customers can try. Finding the tool that most suits a particular individual, vehicle, or circumstance, may take some experimentation, but users must always make safe use of their chosen tools a top priority.