When choosing ball joint separator you need know

If you require knowing auto repair tool, first you need to make sure to know about viable ball joint separator set. 

A ball joint separator is an easy tool used to separate ball joints from the suspension components they are attached to on a vehicle. Because these components have very tight tolerances on the ball joint shaft they sit on, when it comes time for them to be replaced it is rare for them to simple slip off when the nut is removed. The design of the ball joint separator allows it to slip between the ball joint and the component it is attached to and essentially wedge it out.

Learn more ball joint separators via autotoolsdepot.com.

4 types of ball joint separator(1)

A car's ball joint separators play an essential part in its handling, insofar as they prevent movement slack through the control arms, stabilisers, and steering knuckles. Automobile undercarriages differs widely, and so do ball joint separator designs. Before undertaking their next ball joint replacement job, mechanics should understand what is needed to secure the best deal on their preferred ball joint separator.

Fork Type

The fork type separator requires mechanics to use impact force. Mechanics wedge the fork of the tool into the ball joint and strike the end with a hammer, popping the ball joint out of its housing. It is a traditional method, and suitable for large vehicles with large wheel hub spaces that allow for greater freedom of movement. However, this method does demand a good deal of care. These tools are available in various lengths.

Laser Scissor Type

The laser scissor format separator offers a gentler alternative to the fork method. It allows users to remove ball joints effectively with a simple screwing action, thereby reducing the risk of self-injury or damage to surrounding parts. This type of ball joint separator is especially useful in particularly confined spaces that do not allow for easy hammering access. These separators generally consist of robust heat-treated drop forged steel. Their jaw spans typically range between 18 and 38 mm.

The choice of oil filter wrench you may know

First, you will need to find out what size filter you have on your vehicle.

Knowing the size of the filter will narrow down the choice of which oil filter wrench is most suitable for you. This information can be found in the vehicle owner's manual, or if you do not have your owner's manual, you can simply measure the diameter of the filter yourself.

The belt and automatic oil filter wrenches come with a handle and do not need any extra tools. The automatic wrench reduces user input as it is automatic, while the belt wrench requires manual tightening.

On the other hand, if you do own tools such as a hand ratchet that fits a square drive, or a spanner that fits around a hexagonal drive, then it could be a cheaper option choosing the web or chain strap wrenches.

So, when choosing which oil filter wrench to use, find out the size of filter you are removing and if you need an all in one, no tools needed oil filter wrench, or an adapter that fits your square drive tools.

Do you know the advantages of oil filter wrench?

Auto Tools oil filter wrench is one of the most commonly used oil filter wrenches. 

Oil Filter Wrench has an adjustable strap that fits on oil filters whose diameter ranges from 3.25 inches to 3.75 inches.

Another advantage of oil filter wrench is that it is readily available in most automotive shops and online retailers in the world. Therefore, finding a place to purchase one won't be a problem.

Its elongated handle is easy to grasp and is fitted with a non-slip material. This tool is made of stainless steel hence can withstand regular use, and it lasts long.

Do an experiment about air duster gun (2)

We continue to do an experiment about air duster gun.

Now we have everything lets get going. Take the pen apart as shown. You don't need anything but the outer casing and the pointy plastic tip. Take the spring and flick it across the room for you to find later (or don't).

Now take the plastic straw from the air duster and stick it into where the ink tube was not so long ago. It probably wont fit too snugly so this is where the lighter (or stove-top) comes in. CAREFULLY melt the tip until it's barely soft and roll it on the desktop to shrink the diameter of the tip to fit the straw fairly snugly.

It should be fairly difficult to pull it off of the straw because it will be holding pressure later. Now we need to finish up. If my vague description haven't helped, the pictures should help.

We are air duster gun manufacturer in China, you can send your email toinfo@autotoolsdepot.com.

Do an experiment about air duster gun (1)

Air Dusters aren't just for cleaning things, they are also potential propellant. Here you will see how to launch small objects at reasonable velocity (i used erasers).

First lets go grab what we need. Of course you need the air duster gun with the little plastic straw. Nowdays this is available at Target and Wal-Mart or other places like that, along with electronics stores. Get whatever is cheapest, but it must have the plastc straw.

Now we need a click pen. The one pictured works best (and they are mostly free from car delerships) because it comes apart nicely.

We also need a lighter, or like I did the first time you can use a stove if you are really careful. A projectile can be found later, I use erasers from cheap pencils.

DISCLAIMER: this project can possibly injure somebody. I am not responsible for any injuries, damages or deaths related to the fabrication or usage of this product. Allways use common saftey sense and proper saftey equipment while fabricating or using this product. It can shoot over 100ft and still sting a little.

We are air duster gun manufacturer in China, you can send your email toinfo@autotoolsdepot.com.