How to change filter?

Before installing your filter, lightly coat its rubber seal with fresh oil. The oil filter wrench also has to be changed. Install a new filter in it and tighten the lid. If you get custom built-in tool storage, power tail gates and more, multiple additions of things you may not use often or even need will add to the price as well. Any expert doesn't need to do it. If the service engine soon light doesn't come back on. Problem with these Ford engines is the coil pack electrodes corrode causing misfire and the check engine light to go on! Alignment issues will accelerate tires wear and cause your engine to work harder. When switched to the "Main" position, fuel flows from the main tank directly to the engine and the fuel gauge indicates the amount of fuel in the main tank.

We are one of leading auto engine tool manufacturers, welcome to consult us!

Do you know tire inspection?

Today I will tell you some test about auto, hoping to help you. You'd better have a tire repair tool.

External test

1. remove the wheel from the car care

2. tire inflation – in control under pressure recommended by the manufacturer (based on tire-wall)

3. the tires into the testing tank, leak parts have been found. High pressure leak appears under certain conditions (in the load overload effect), then you will need to use a leak detector to find the damage area. Caution test, beware many of the damaged air leakage.

4. refer to "not (industry standard)" (outside). When the tires to determine needs and can be patched with a marker in the repairability of tires before doubt, you should not repair steps.

Internal test

5. remove the tire from the wheel on the ground.

6. in the light of "can not be repaired (industry standard)" (inside). When the tires to determine needs and can be patched with a marker in the tire marks on the internal tire damage done.

7. removed cause tire damage foreign material, carefully measured to ensure passenger car tire damage the diameter of 1/4 inches or less, light (middle), truck tire damage the diameter of 3/8 inches or less. If the damage exceeds the above, that should be given to removing the tire to comprehensive professional repair service repair make larger cross section.

8. use the probe, remove it from the outside insert the tire until it through the airtight layer 1/4 inch. Be careful to prevent sticking out of the other hole.

9. the probes inserted into the cut holes to the point of keeping the "12 o'clock" position, the mushroom nail hole close to a probe into injury, makes mushroom nail the center hole Center to injury.

10. when the penetration angles less than 25 degrees, use a holistic approach to repair (full mushroom nail).

11. when the penetration angles greater than 25 degrees, repair must be two discrete methods (principles equivalent to separate the mushroom patch parts of the nail and rod).

12. tyre placed on the wide tires, makes wound hole in "4 o'clock" or "8 o'clock" position. -Bead too open.

Is engine washing gun for you?

Our air engine washing gun is the perfect tool for not only cleaning the engine bay, but also anywhere around the home or workshop. Designed to be filled with detergents and non-corrosive cleaning products, the cleaning gun works its magic allowing you to not only get into those hard to reach spaces, but cut through the grease and grime at the same time. The 750mL container allows you to focus on the job at hand, and an included simple, Nitto style fitting gives peace of mind.

• 750mL container capacity
• Nitto style air fitting included
• Ideal for cleaning or degreasing
• Suitable for non-acidic/non-corrosive liquids
• Powder coated gun body with aluminium container

If you want engine washing gun, please contact us!

How much you know ball joint separator?

We are ball joint separator manufacturer and we will provide some knowledge about ball joint separator.

The first signs of a failing ball joint include loud banging over bumps and/or sloppy steering as the joint separates out of its socket. A typical safety inspection should measure the amount of motion in your ball joint, and only allow a safe amount to pass. You can test ball joint play yourself on McPherson spring struts that do not put any load on the ball joint by lifting the car and manhandling the wheel. This design is rare, however, because most suspension springs apply constant pressure on the assembly.

If your car has a spring that puts load on either the upper or lower ball joint, you will need to remove that spring pressure by positioning your jack under the control arm and jacking it a few inches up to relieve the spring pressure on the ball joint. If the design allows, you can use a special ball joint support tool like the one made for the Saab 900 to hold everything in place. You can also relive tension with standard spring compressors, which is a common way of doing this.

If you find ball joint separator supplier in China, you can send your email to info@autotoolsdepot.com.

How much you know battery tester?

It's important to test your battery and electrical system regularly, not just when it’s starting to show signs of weakness. So, it is necessary to have a battery tester. Proactively testing it (or making sure your mechanic does) twice a year will help reduce your chances of failure. Most retailers offer a simple free five minute battery test. Use our Find a Retailer for a location near you to get a free battery test.

Fully charged automotive batteries should measure at 12.6 volts or above. When the engine is running, this measurement should be 13.7 to 14.7 volts. If you don’t have a multimeter to tell you the voltage of your battery, you can do a test of your electrical system by starting the car and turning on the headlights. If they are dim, that indicates the lights are running off the battery and that little or no charge is being produced by the alternator. If the lights get brighter as you rev the engine, it means the alternator is producing some current, but may not be producing enough at idle to keep the battery properly charged. If the lights have normal brightness and don’t change intensity as the engine is revved, your charging system is probably functioning normally. If you’ve been experiencing problems with your battery system and the headlight test checks out okay, you should check whether or not the battery is holding a charge, or if something on the vehicle is discharging it.

We provide high quality battery tester.

Do you know magnetic tray?

Magnetic tray has many uses. Keep loose nuts, screws and other small metal items in reach. Smooth stainless steel trays have powerful ceramic magnets with rubber covers in the base to secure the tray to a metal toolbox or table while keeping important metal pieces at hand. Store metal parts and tools during assembly and disassembly. Ideal for mechanics, craftsmen and hobbyists.

• Works in any position - flat, sideways or upside down
• Heavy gauge, stainless steel with rubber base to prevent scratching
• Great for jobsite, garage, office and home

Learn more magnetic tray via www.autotoolsdepot.com.

Do you learn the development of auto tools?

With the improvement of automotive technology, the growth of car ownership, the development of car repair market, there are a number of modern enterprises entering the auto maintenance industry in the past decade. They began to produce and provide various professional auto maintenance equipment, especially Ball Joint Separator, Disc Brake Piston Separator, Coil Spring Compressor. There are a large number of overseas exports, we are one of them.

In national policy guidance, the Chinese auto maintenance industry has a thriving development. China's auto maintenance equipment after years of expansion, already has a considerable scale and pace of development. China is currently engaged in auto maintenance equipment development, production and marketing enterprises, about 1500, the annual output of about 10 billion. China continued prosperity auto maintenance industry trend, business volume and revenue continued to grow, equipment manufacturers to maintain rapid growth within the industry business model shift.

Welcome to consult auto tools from China, welcome to consult engine tools from our company.

How does the air duster gun work?

Air duster gun is the principle of using air amplification, effectively reducing the consumption of compressed air, resulting in a strong and accurate airflow, and drive the surrounding air to work together. Dust guns are mainly used for dust, dust, or foreign matter on any type of workpieces for use in factories, mechanical workshops, woodworking and installation. Can be used in some of the hands of some of the relatively narrow, high, inside the machine parts and trachea cleaning work.

Our company specializes in manufacture, supply and export air duster gun. It has always been our focus to manufacture the finest Air Tools / Pneumatic Tools and to deliver them on time with attentive after-sales service.

Quick detail of air duster gun

Here is a quick detail of air duster gun.

* DG/TG series air duster gun tire inflator gun

* Body material:Plastic,zinc alloy,aluminum alloy

* air blow nozzle material steel

* Air blow nozzle length from 16mm~500mm upon requirement

* maximum working pressure 1.0Mpa

* various joint connector for option

* compact design,flexible application for any site work

* easy to operate,fast connect to air source

* big flow,high stability and long service life

Learn more air duster gun via www.autotoolsdepot.com.

Emergency tire repair tools you must have

There are usually some tire repair tools in your car.

1. Car inflatable pump (around 200 yuan): This is an essential tool for tire repair, although some expensive but when you really use it when it will be very worth it. The market also has a lot of cheap car inflatable pump, when the selection of more contrast, choose their own vehicle inflatable pump.

2. Emergency tires hand cone and tape (20 yuan): hand cone and strips are basically sold, 5 strips can also be used after the single buy, the price of 5 yuan or so.

3. Pliers (10 yuan or so): This demonstration we use the ordinary pliers, but the best time to choose the tip of the tire when the taper, so you can easily remove the tires of the piercing thing.

4. Wallpaper knife (5 yuan): wallpaper knife is the last to repair the tire repair tape to use the tools.

5. Water (2 yuan): water is used to check the leak when the need to use the emergency time can also be used to replace the beverage

5 Best Auto Emergency Tools

With good fortune, you may never need to use one of these auto emergency tools in an accident situation, but that does not mean that you should not buy one.

As well as having a hammer, many glass breakers also incorporate other survival tools, which can prove to be equally as crucial in the event of an emergency. A seat-belt cutter, for example, will enable you free yourself and others quickly. A flashlight will aid vision in the dark, or provide you with the means to signal for help.

Multi-Function Safety Tool: The Swiss+Tech ST81010 BodyGard!

Always Within Reach With a Keychain: The Resqme!

3 types of oil filter wrench

There are three oil filter wrenches in our common market. Here I will tell you as followings:

1. three-jaw filter wrench

Instructions for use: to be used with a sleeve handle or wrench, the internal design of the planetary row of transmission mechanism, according to the size of the oil filter automatically tune three claw size.

Design features: still need to be used in conjunction with the sleeve, but a three-jaw wrench can correspond to a variety of sizes of machine filter, improved than the previous species; but the internal structure of complex, if damaged maintenance.

2. ring filter wrench

Instructions for use: The structure is an adjustable size of the ring, the inside of the ring design for the jagged. When used in the filter on the top of the corrugated surface, pull the handle wrench ring will be based on the appropriate size of the filter card in the corrugated surface, the successful completion of the disassembly work.

Design features: simple, convenient, can correspond to a variety of sizes of machine filter, do not use with other parts, can improve work efficiency.

3. Clamp filter wrench

Instructions for use: This filter wrench is a modified product of pliers, similar to the use of carp pliers.

Design features: simple, easy to carry, but can correspond to the machine filter size is less, is a simple device.

Choose home car washing water gun you need know

In recent years, with the improvement of people's living standards, home car engine washing gun is more and more popular with the homes of ordinary people, espcially the majority of car owners, people love flowers, housewives accepted, with its convenient, practical, water and many other advantages. Here I will tell you some methods and techniques about buying such products, hoping that is helpful to you.

1. Faucet fittings: This is a problem the buyer should be most notable. Currently faucet fittings are generally screw-type, fixed type and caliber of rubber several common universal type

2. Hose Connector: Two piece hose connector and detachable.

3. Water: Water is so much a component of the most mixed, which is generally divided into two categories: woven plastic tube and pipe.

4. Gun: the type of gun is great variety and quality vary widely, according to the material to points Generally speaking generally have the following: zinc alloy of copper head gun, copper core plastic guns, plastic gun galvanized, all-plastic gun.

Speaking of gun, I want to say more. Auto Tools Depot is a leading manufacturer & exporter of auto tools, we provide high quality air duster gun, spray gun, foam gun for many years. If you need, welcome to result us.

Auto Repair Tool - Ball Joint Separator

Auto Repair Costs Jump 10%, But There's Good News, Too – The expense of repair hopped however the quantity of ball joint separator shop visits has diminished. This article is packed with awesome measurements. Keeping in mind we are discussing the expense of repair here is an extraordinary article on the most costly (and least expensive) states for auto repairs.

Extraordinary administration apparatuses and instruments that you "utilize no one but once" can be exceptionally costly so we are building up a rental project which will make ball joint separator accessible to you at a considerable reserve funds.

Auto repair you must know

Auto Repair is something no driver needs to manage, yet it is a truth of vehicle proprietorship. Autos require support and repairs, and the more you keep a vehicle and the more miles you put on it, the all the more frequently you should administration and repair your auto. Important auto repairs ought NOT to be put off as this builds the danger of greater and more costly issues not far off. In like manner, if your vehicle requires upkeep, for example, an oil change, channels, brakes or whatever, don't put it off as this may trade off the dependability of your vehicle and driving wellbeing.

If you require knowing auto repair tool, first you need to make sure to know about viable ball joint separator set. A ball joint separator is an easy tool used to separate ball joints from the suspension components they are attached to on a vehicle. Because these components have very tight tolerances on the ball joint shaft they sit on, when it comes time for them to be replaced it is rare for them to simple slip off when the nut is removed. The design of the ball joint separator allows it to slip between the ball joint and the component it is attached to and essentially wedge it out.

Oil filter wrench you may know more

An oil filter wrench is a tool for removing spin-on type oil filters. These filters are smooth, cylindrical canisters with knurling on the bottom that are difficult to grip, especially when they are oily.

One common type of wrench is shown on the right. The loop of chain is placed around the filter, and the bar is turned anticlockwise by hand until the chain wraps itself tightly around the filter. A socket wrench or adjustable spanner is then used to turn the hexagonal bar further in the same direction. This increases the tension in the chain, which bites into the soft metal casing of the oil filter which helps prevent slippage.

Another type uses a metal band that is attached at both ends to a handle. The looped band is placed around the filter and the handle is turned anticlockwise, which puts tension on the band, causing it to grip the filter.

A third common type of wrench utilizes a metal or plastic cup that is shaped much like a socket. The cup is placed on the end of the filter, which engages the knurling. A socket or wrench is then used to loosen the filter. Volkswagen Group and BMW cars require this type of wrench to remove their filters (or the lid of the filter housing, where a non-cartridge filter is used).

What is ball joint separator?

We are ball joint separator manufacturer and we will provide some knowledge about ball joint separator.

The first signs of a failing ball joint include loud banging over bumps and/or sloppy steering as the joint separates out of its socket. A typical safety inspection should measure the amount of motion in your ball joint, and only allow a safe amount to pass. You can test ball joint play yourself on McPherson spring struts that do not put any load on the ball joint by lifting the car and manhandling the wheel. This design is rare, however, because most suspension springs apply constant pressure on the assembly.

If your car has a spring that puts load on either the upper or lower ball joint, you will need to remove that spring pressure by positioning your jack under the control arm and jacking it a few inches up to relieve the spring pressure on the ball joint. If the design allows, you can use a special ball joint support tool like the one made for the Saab 900 to hold everything in place. You can also relive tension with standard spring compressors, which is a common way of doing this.

If you find ball joint separator supplier in China, you can send your email to info@autotoolsdepot.com.

Have You Mastered The Correct Posture Of Using Air Duster Gun?

The Air Duster Gun has a simple structure and is easy to use, but it requires proper using.

There are many factors that affect the use of guns,like painted objects,painted materials,and even seasons.The key to the use of the gun is to adjust the control of the knob,the distance between the grasping of the spray gun and the speed of the user’s movement,as well as the proximity of the layers of the overlap.The spraying distance, spraying running and spray pattern is three spraying Principles,they are also the basis of spraying technology,must be familiar with,and strictly abide by.

Spray guns are essential for efficient coating. With the progress of manufacturing technology and the application of new materials, modern spray gun is moving into the direction of high durability, fine atomization , spray gun structure is more and more scientific.Although there are many types of guns,their structures are roughly same.Generally it is constituted with tip, adjusting knob and body.

Our company is an air duster gun manufacturer, we provide varies of guns and knowledge about them.

Ball joint separator you may know

We are ball joint separator manufacturer and we will provide some knowledge about ball joint separator.

The first signs of a failing ball joint include loud banging over bumps and/or sloppy steering as the joint separates out of its socket. A typical safety inspection should measure the amount of motion in your ball joint, and only allow a safe amount to pass. You can test ball joint play yourself on McPherson spring struts that do not put any load on the ball joint by lifting the car and manhandling the wheel. This design is rare, however, because most suspension springs apply constant pressure on the assembly.

If your car has a spring that puts load on either the upper or lower ball joint, you will need to remove that spring pressure by positioning your jack under the control arm and jacking it a few inches up to relieve the spring pressure on the ball joint. If the design allows, you can use a special ball joint support tool like the one made for the Saab 900 to hold everything in place. You can also relive tension with standard spring compressors, which is a common way of doing this.

If you find ball joint separator supplier in China, you can send your email to info@autotoolsdepot.com.

Method of Maintenance of Air Blower Gun

In the maintenance of the soot blower, the power supply must be cut off and the steam line valve in front of the blower valve shall be turned off, in case the air duster gun can initiate or other electrical accidents. 

Regularly check the seals for leakage. If there is a leak, adjust the compression of the packing properly; The packing gland can be replaced if the problem is still unsolved. When the sealing ring of the hollow shaft is replaced, the V type opening should be loaded in the direction of the stem. 

If there is a leak after the valve is closed, it is indicated that the combination of the seat ring and the disc shall be worn or deformed, and shall generally be re-ground the sealing surface. The body must be replaced if the cover is damaged enough to be insufficient to solve. 

Grease the oil regularly. The decelerate box is once a month, starting arm and copper sleeve once a week. 

The air duster gun should be disintegrated once a year, often check the stroke switch and regularly clean up the soot on the blower. 

If the load of the motor is too heavy, check that the ash gun is bent. If bending should be taken out straighter in time. 

When use air duster gun you must know

There are many air duster guns in car industry, here I will tell you some considerations you must know as followings:

1. Must be installed in accordance with the operating instructions before use.

2. Blowing guns need to be connected to the compressor.

3. Keep the dust gun clean, oil free and fouling.

4.Regular cleaning of the dust gun to prevent a large number of other objects accumulated in the dust gun parts above, clean, should cut off the power.

5. Can not be used in environments containing flammable gases and large amounts of dust.

6. Non-professional personnel can not be repaired without authorization.

Our company is an air duster gun manufacturer, we provide varies of guns and knowledge about them.

The steps of changing oil(2)

When you have an oil filter wrench, you also need do as followings:

6. After the oil has drained (give it 10-30 minutes for a good drain if you have the time), wipe away oil residue from the oil pan and put the drain plug back in. Tighten it firmly, but don’t overdo it. Your owner’s manual will have the exact torque required.

Do me (and other animals) a favor, clean up oil leaks and don’t dispose of oil in your yard, streams, or waste-water drains. Your favorite Advance store will safely dispose of your used oil for free! Available at most of our 3,500 stores (unless prohibited by law).

7. Reposition your drain pan by the oil filter and remove it using your oil filter wrench (or hand if it will budge). Some wrenches work from the end, while others wrap around the filter.

8. If your filter still won’t budge, puncture it with a screwdriver at its lowest point to drain, then use the same screwdriver to spin off the filter. A little more oil will come out when you spin off the filter, so have your rags handy.

9. Apply a film of clean oil to the top of the new filter gasket. Then spin the filter on using only your hand. Go ¾ of a turn after you feel the gasket make contact with the engine after spinning it on.

oil change tips10. Double check the filter and drain plug for tightness, then fill your engine with the recommended viscosity and amount of motor oil. (Again, your owner’s manual will provide this).

11. Determine your oil level using the dipstick, then check for any leaks. Start the engine and check for leaks again. Bring used motor oils to Advance for proper disposal or recycling.

Well, that’s a wrap. You can now safely do your own oil ch

The steps of changing oil(1)

First, you must have an oil filter wrench. Then I will tell you 10 steps of changing oil as followings:

1. Securely raise your vehicle on ramps or jack-stands (use a jack lift for the latter). Makes sure to put blocks behind your tires. If you can safely get under your vehicle without needing to raise it, then go for it.

2. Warm up the engine for a couple minutes to get the oil warm (but not too long or the oil will be hot). Raise your hood and open the oil cap on top of your engine to let the old oil drain faster.

3. Get under the car and position your drain pan under the oil plug (account for the initial stream of oil shooting out further than directly under the plug).

4. Using your wrench, loosen the plug a few turns. Then finish loosening the plug with your hand, quickly pulling it away when the oil is starting to drain out. Be careful of hot motor oil (gloves help in this case).

5. Wipe the drain plug while the oil drains and inspect it for bent or broken threads. Replace the sealing washer if cracked or worn, or use a new metal crush washer if needed.

I will tell you the others in next news, learn more oil filter wrench via www.autotoolsdepot.com.

Do you hear ball joint separator?

We are ball joint separator manufacturer and we will provide some knowledge about ball joint separator.

The first signs of a failing ball joint include loud banging over bumps and/or sloppy steering as the joint separates out of its socket. A typical safety inspection should measure the amount of motion in your ball joint, and only allow a safe amount to pass. You can test ball joint play yourself on McPherson spring struts that do not put any load on the ball joint by lifting the car and manhandling the wheel. This design is rare, however, because most suspension springs apply constant pressure on the assembly.

If your car has a spring that puts load on either the upper or lower ball joint, you will need to remove that spring pressure by positioning your jack under the control arm and jacking it a few inches up to relieve the spring pressure on the ball joint. If the design allows, you can use a special ball joint support tool like the one made for the Saab 900 to hold everything in place. You can also relive tension with standard spring compressors, which is a common way of doing this.

If you find ball joint separator supplier in China, you can se

4 types of ball joint separator(2)

Automobile undercarriages differs widely, and so do ball joint separator designs. Before undertaking their next ball joint replacement job, mechanics should understand what is needed to secure the best deal on their preferred ball joint separator.

Hydraulic Type

Hydraulic format ball joint separators support between 8 and 12 tonnes of weight. As with the scissor type, they are suitable for confined spaces and consist of heavily reinforced steel, but jaw widths can span up to 56mm. Available both separately and in ball joint separator kits, they are ideal for commercial vehicles and small lorries.

Choosing Tool Type

Although the previously discussed ball joint separator formats are among the most well-liked by mechanics, there are many other types that customers can try. Finding the tool that most suits a particular individual, vehicle, or circumstance, may take some experimentation, but users must always make safe use of their chosen tools a top priority.

When choosing ball joint separator you need know

If you require knowing auto repair tool, first you need to make sure to know about viable ball joint separator set. 

A ball joint separator is an easy tool used to separate ball joints from the suspension components they are attached to on a vehicle. Because these components have very tight tolerances on the ball joint shaft they sit on, when it comes time for them to be replaced it is rare for them to simple slip off when the nut is removed. The design of the ball joint separator allows it to slip between the ball joint and the component it is attached to and essentially wedge it out.

Learn more ball joint separators via autotoolsdepot.com.

4 types of ball joint separator(1)

A car's ball joint separators play an essential part in its handling, insofar as they prevent movement slack through the control arms, stabilisers, and steering knuckles. Automobile undercarriages differs widely, and so do ball joint separator designs. Before undertaking their next ball joint replacement job, mechanics should understand what is needed to secure the best deal on their preferred ball joint separator.

Fork Type

The fork type separator requires mechanics to use impact force. Mechanics wedge the fork of the tool into the ball joint and strike the end with a hammer, popping the ball joint out of its housing. It is a traditional method, and suitable for large vehicles with large wheel hub spaces that allow for greater freedom of movement. However, this method does demand a good deal of care. These tools are available in various lengths.

Laser Scissor Type

The laser scissor format separator offers a gentler alternative to the fork method. It allows users to remove ball joints effectively with a simple screwing action, thereby reducing the risk of self-injury or damage to surrounding parts. This type of ball joint separator is especially useful in particularly confined spaces that do not allow for easy hammering access. These separators generally consist of robust heat-treated drop forged steel. Their jaw spans typically range between 18 and 38 mm.

The choice of oil filter wrench you may know

First, you will need to find out what size filter you have on your vehicle.

Knowing the size of the filter will narrow down the choice of which oil filter wrench is most suitable for you. This information can be found in the vehicle owner's manual, or if you do not have your owner's manual, you can simply measure the diameter of the filter yourself.

The belt and automatic oil filter wrenches come with a handle and do not need any extra tools. The automatic wrench reduces user input as it is automatic, while the belt wrench requires manual tightening.

On the other hand, if you do own tools such as a hand ratchet that fits a square drive, or a spanner that fits around a hexagonal drive, then it could be a cheaper option choosing the web or chain strap wrenches.

So, when choosing which oil filter wrench to use, find out the size of filter you are removing and if you need an all in one, no tools needed oil filter wrench, or an adapter that fits your square drive tools.

Do you know the advantages of oil filter wrench?

Auto Tools oil filter wrench is one of the most commonly used oil filter wrenches. 

Oil Filter Wrench has an adjustable strap that fits on oil filters whose diameter ranges from 3.25 inches to 3.75 inches.

Another advantage of oil filter wrench is that it is readily available in most automotive shops and online retailers in the world. Therefore, finding a place to purchase one won't be a problem.

Its elongated handle is easy to grasp and is fitted with a non-slip material. This tool is made of stainless steel hence can withstand regular use, and it lasts long.

Do an experiment about air duster gun (2)

We continue to do an experiment about air duster gun.

Now we have everything lets get going. Take the pen apart as shown. You don't need anything but the outer casing and the pointy plastic tip. Take the spring and flick it across the room for you to find later (or don't).

Now take the plastic straw from the air duster and stick it into where the ink tube was not so long ago. It probably wont fit too snugly so this is where the lighter (or stove-top) comes in. CAREFULLY melt the tip until it's barely soft and roll it on the desktop to shrink the diameter of the tip to fit the straw fairly snugly.

It should be fairly difficult to pull it off of the straw because it will be holding pressure later. Now we need to finish up. If my vague description haven't helped, the pictures should help.

We are air duster gun manufacturer in China, you can send your email toinfo@autotoolsdepot.com.

Do an experiment about air duster gun (1)

Air Dusters aren't just for cleaning things, they are also potential propellant. Here you will see how to launch small objects at reasonable velocity (i used erasers).

First lets go grab what we need. Of course you need the air duster gun with the little plastic straw. Nowdays this is available at Target and Wal-Mart or other places like that, along with electronics stores. Get whatever is cheapest, but it must have the plastc straw.

Now we need a click pen. The one pictured works best (and they are mostly free from car delerships) because it comes apart nicely.

We also need a lighter, or like I did the first time you can use a stove if you are really careful. A projectile can be found later, I use erasers from cheap pencils.

DISCLAIMER: this project can possibly injure somebody. I am not responsible for any injuries, damages or deaths related to the fabrication or usage of this product. Allways use common saftey sense and proper saftey equipment while fabricating or using this product. It can shoot over 100ft and still sting a little.

We are air duster gun manufacturer in China, you can send your email toinfo@autotoolsdepot.com.

Do you hear ball joint separator?

We are ball joint separator manufacturer and we will provide some knowledge about ball joint separator.

The first signs of a failing ball joint include loud banging over bumps and/or sloppy steering as the joint separates out of its socket. A typical safety inspection should measure the amount of motion in your ball joint, and only allow a safe amount to pass. You can test ball joint play yourself on McPherson spring struts that do not put any load on the ball joint by lifting the car and manhandling the wheel. This design is rare, however, because most suspension springs apply constant pressure on the assembly.

If your car has a spring that puts load on either the upper or lower ball joint, you will need to remove that spring pressure by positioning your jack under the control arm and jacking it a few inches up to relieve the spring pressure on the ball joint. If the design allows, you can use a special ball joint support tool like the one made for the Saab 900 to hold everything in place. You can also relive tension with standard spring compressors, which is a common way of doing this.

If you find ball joint separator supplier in China, you can send your email to info@autotoolsdepot.com.

4 types of ball joint separator(2)

Automobile undercarriages differs widely, and so do ball joint separator designs. Before undertaking their next ball joint replacement job, mechanics should understand what is needed to secure the best deal on their preferred ball joint separator.

Hydraulic Type

Hydraulic format ball joint separators support between 8 and 12 tonnes of weight. As with the scissor type, they are suitable for confined spaces and consist of heavily reinforced steel, but jaw widths can span up to 56mm. Available both separately and in ball joint separator kits, they are ideal for commercial vehicles and small lorries.

Choosing Tool Type

Although the previously discussed ball joint separator formats are among the most well-liked by mechanics, there are many other types that customers can try. Finding the tool that most suits a particular individual, vehicle, or circumstance, may take some experimentation, but users must always make safe use of their chosen tools a top priority.

4 types of ball joint separator(1)

A car's ball joint separators play an essential part in its handling, insofar as they prevent movement slack through the control arms, stabilisers, and steering knuckles. Automobile undercarriages differs widely, and so do ball joint separator designs. Before undertaking their next ball joint replacement job, mechanics should understand what is needed to secure the best deal on their preferred ball joint separator.

Fork Type

The fork type separator requires mechanics to use impact force. Mechanics wedge the fork of the tool into the ball joint and strike the end with a hammer, popping the ball joint out of its housing. It is a traditional method, and suitable for large vehicles with large wheel hub spaces that allow for greater freedom of movement. However, this method does demand a good deal of care. These tools are available in various lengths.

Laser Scissor Type

The laser scissor format separator offers a gentler alternative to the fork method. It allows users to remove ball joints effectively with a simple screwing action, thereby reducing the risk of self-injury or damage to surrounding parts. This type of ball joint separator is especially useful in particularly confined spaces that do not allow for easy hammering access. These separators generally consist of robust heat-treated drop forged steel. Their jaw spans typically range between 18 and 38 mm.

When choosing ball joint separator you need know

If you require knowing auto repair tool, first you need to make sure to know about viable ball joint separator set. 

A ball joint separator is an easy tool used to separate ball joints from the suspension components they are attached to on a vehicle. Because these components have very tight tolerances on the ball joint shaft they sit on, when it comes time for them to be replaced it is rare for them to simple slip off when the nut is removed. The design of the ball joint separator allows it to slip between the ball joint and the component it is attached to and essentially wedge it out.

Learn more ball joint separators via autotoolsdepot.com.

Do you know the advantages of oil filter wrench?

Auto Tools oil filter wrench is one of the most commonly used oil filter wrenches. 

Oil Filter Wrench has an adjustable strap that fits on oil filters whose diameter ranges from 3.25 inches to 3.75 inches.

Another advantage of oil filter wrench is that it is readily available in most automotive shops and online retailers in the world. Therefore, finding a place to purchase one won't be a problem.

Its elongated handle is easy to grasp and is fitted with a non-slip material. This tool is made of stainless steel hence can withstand regular use, and it lasts long.

Do an experiment about air duster gun (2)

We continue to do an experiment about air duster gun.

Now we have everything lets get going. Take the pen apart as shown. You don't need anything but the outer casing and the pointy plastic tip. Take the spring and flick it across the room for you to find later (or don't).

Now take the plastic straw from the air duster and stick it into where the ink tube was not so long ago. It probably wont fit too snugly so this is where the lighter (or stove-top) comes in. CAREFULLY melt the tip until it's barely soft and roll it on the desktop to shrink the diameter of the tip to fit the straw fairly snugly.

It should be fairly difficult to pull it off of the straw because it will be holding pressure later. Now we need to finish up. If my vague description haven't helped, the pictures should help.

We are air duster gun manufacturer in China, you can send your email toinfo@autotoolsdepot.com.

Do an experiment about air duster gun (3)

At this point, you should be seeing the whole air duster gun part. Pretty simple, but I am long winded and must overly explain everything. So we have the Gun finished now, but we have no projectile. What are we going to do? Calm down, i have this under control.

After years [and by years i men about 2 min] of R&D; I discovered that your average eraser from an el cheapo [or free] wooden pencil works very well. If its too small, try a different eraser, there are 2 normal sizes and the biggest one works the best.

I have found that using some oil [i use reel oil, but 3 in 1 oil or similar will work] helps out a lot with getting a snug but not too snug fit with the eraser. If the eraser fits too snugly, the whole barrel will go flying, which is pretty cool, but not as fast. If you shove the eraser down too far, you can use the straw to push it back out to a good firing fit.

In my tests, my basement is a little over 100ft long and it goes all the way to the other side without too much arc. Be carefull when shooting, it can sting, and possibly maim, so use common sense and if you lack this, do not make my project. ENJOY!